Simple Foamcore Farm Houses

 Sometimes you just need some quick and decent looking terrain. 

 Scenario 4 of Stargrave Hope Eternal campaign is set on a world far out in the boonies of the galaxy, and as such is a little lacking in tech. The settlement is described in the book as being a combination of prefab structures, homes made from locally available materials, and one tower made from a recycled fuel pod. You need between 6-10 structures for the scenario. I own 2 small 3D printed prefab huts and so need at least 4 more structures, one of which needs to be a tower, so I need to make at least 3 houses. The game is played on a 3'x3' board, but the village needs to be at least 8" away from any board edge so none of these should be very big...

 Keeping the size manageable had me laying out a couple of different size bits of paper on the board, and placing some minis in and around them. 2"x3" was tiny, and 4"x6" was too big, but a 3"x5" note card felt just about perfect. Big enough for a full sized door and a couple of windows, but not so big that they'd dominate the table.  

 Not wanting to spend a lot of time or money on them, I grabbed a scrap of foam core that I'd been saving, and got to measuring. Prior experience reminded me that I couldn't just cut out 3" and 5" wall sections because then the footprint would be too big. I opted to trim the long edges by the thickness of the foam core so that the walls would fit neatly on the 3x5 piece that would serve as the base/floor of the huts. 

I kept the height of the walls at 2" knowing the roof would greatly increase the height of the finished builds. I measured out the doors and windows using a 1" square base, then cut them all out. I opted for one door for each building, and 3 windows. 

I turned on my glue gun to get it hot, then I pulled out some aluminum foil, rolled it into a ball, and rolled it all over the exterior sides of the walls and the floor. It really is a fantastic way to add texture to cheap foam core. Once done, it was time to get gluing. 

 

Not perfect. My measurements were not exact, but close enough. I do like how it's possible to shoot through a building. Then it was time to grab the cardboard recycling and dig out a cardstock box and start cutting thin strips. I was actually more careful with this part than I was cutting the foam.  I framed out the corners and all the windows and doors. 

 All told this was about 2 hours worth of work. I then brought it down to my painting desk and slapped on a heavy coat of mod podge mixed with black craft paint, and once dry, followed that up with a heavy drybrush of antique white.

 I was unsure at this point whether I wanted to paint the interior walls or tint the exterior... I decided to try tinting the exterior using just a tint bit of watered down speedpaint.

 And then onto the roof! My original plan was a standard sloped roof, but my cousin suggested an asymmetrical gable with offset ridge, so that it might look a little less average medieval fantasy 

Once I had the foamcore frame I used cardstock to make the roof, and then started cutting and gluing the shingles... This was a pain to do, and messy.  

I was finally reminded that you can do whole strips and it's a much easier process! Also less messy with the glue and looks neater. It was almost enough to make me redo the other 2... almost.  

Then it was time to put a hole in the roofs for the chimney pipes. These were made from the tubes inside dog poop bag rolls. I also added some trim to the gables under the roof line.  

 Then it was back to the mod podge, and onto painting! The gables were painted just like the walls with antique white and the zealot yellow speed paint, with the brown for the trim.

 The roof was done with a sponge leftover from a mini blister pack and a soft blue craft paint, with a gentle dry brush of antique white to give them some highlights. 

 

Overall, these are great. Not perfect, by any stretch of the imagination, but solid looking and usable for the games I want them for. I still want to make little HCAV units to fit over the chimney pipes, but that's going to be its own little project. For now, it's onto the fuel pod tower!

The kid decided the houses needed a little something extra, so they all got some stickers. 

 And credit where credit is due, a hefty dose of inspiration came from this video.